Encoding 64 bit Walkthroughs (4 GB limit, AVI corruption)

Update: check out this page for the 64-bit Xvid codec

I encountered a problem today related to walkthrough creation in Revit 2010 64 bit with Vista 64 bit. I was exporting a large walkthrough to uncompressed AVI format, and the file size would reach 4.00 GB (4,294,967,296 bytes), and then corruption of the AVI would result. It appears that a 4 GB limit was being imposed at some point in the walkthrough creation process.

Therefore, I tried to use an encoding format. When using Revit 32 bit, I recall that I had a number of options in the Video Compression ‘codec’ dialog when exporting a walkthrough. However, in Revit 64 bit, I only had a couple of basic options (Microsoft Video 1, Intel IYUV Codec, Full Frames (uncompressed)).

After some searching, and trialling a few different ideas, I found that I could access some decent codecs in this box after installing Shark007’s 64 bit components (link below).

64 bit Encoding Components

In addition to the above, it is recommended that you install Shark007’s 32 bit Codec Pack (link below):
Vista Codec Package 5.5.3 Final

After installing both of the above and restarting Revit (you may also need to restart Windows), I was intermittently able to access an additional filter in the dialog called ‘ffdshow’ – clicking ‘Configure’ opened up a whole range of encoding formats for use!However, there appear to be a few problems:

  1. The ‘ffdshow Video Codec’ encoder only appeared in the Video Compression dialog when a certain ‘Size Crop’ and resolution were selected. For me, the only settings that consistently seemed to work were: Size Crop width = 150 mm, and export resolution 886 x 500.
  2. The corruption still seemed to result if the uncompressed AVI format would have exceed 4 GB (even while using a compressed codec).
  3. Choosing H264 actually crashed Revit.
  4. WMV 8 using libavcodec simply did not proceed past the first frame.

Given the above limitations, my solution at this point is:

  1. Split the walkthrough into parts that have a size less than 4 GB (ie. part 1 = frames 1 to 100, part 2 = frames 101 to 200 etc) and use FULL FRAMES (UNCOMPRESSED) AVI format.
  2. Use VirtualDubMod to ‘append’ these segments together, and
  3. Use VirtualDubMod to ‘Save As…’ a different format. I was able to choose ‘Cinepak’ compression in VirtualDubMod, which turned my approx 5.4 GB uncompressed AVI into a 167 MB file in only about 5 mins of processing time.

After spending quite a few hours trying to make this work in a satisfactory and simple manner, I decided to contact our reseller and lodge a support call. I will let you know if I learn anything helpful.During this investigation, I tried a few things without success. They may be of interest to you (see links below).

Windows Media Encoder 64 bit

Xvid 64 bit

x264 64 bit

0 0 votes
Article Rating
Subscribe
Notify of
guest

3 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Anonymous
Anonymous
14 years ago

Dealing with the same issues right now, I also tried k-lite full 32 and 64 bit with no luck. On my 32bit revit station i find if you open the ffdshow encoder before you run the walk thru the ffdshow codec option is more likely to appear. best luck i have had so far is with the sharky stuff.

David Waligora, LEED-AP

Thanks for posting this. I tried to do the 1-100 process on my computer as well. My system keeps returning "Operation Cancelled by User" at frame 60.

I'm running same setup as you are VISTA 64 + REVIT 64.

I"m going to hunch that maybe Vista could be a culprit. I just got my Windows 7 64 bit in the mail. I'm going to retry the export using your procedures. If it passes, I'll post to ecoBIM and reference this site.

-Dave Waligora

Luke Johnson
14 years ago

Hi David, let me know how things turn out for you. Luke.